The Collection
SS 2026 · 6 Pieces
Power Gown I
SS 2026 · In Progress
▸
Foundation of the Power series. Zero-ease sleeve set. Geometric shoulder pad at 3-point anchor. Merino column skirt — bias-cut with twill tape stay.
Power Gown II
SS 2026 · Complete
▸
Evolved shoulder geometry. Extended column hem. Same sloper family as Gown I — sleeve block transferable.
Power Gown III
SS 2026 · Draft
▸
Statement collar variant. Lapel removed. Same bonded crepe specification. Travel packability confirmed — folds to 28×34cm.
Xanadu
SS 2026 · Complete
▸
Drape-forward construction. No geometric shoulder — contrast piece to Power series. Silk charmeuse with hand-rolled hem.
AnDreeAna
SS 2026 · ⚠ Issue
▸
Bias skirt panel flagged: Merino stretch exceeds spec. Twill tape stay not yet applied. Bodice attachment at risk.
Japanese Transformational
SS 2026 · Concept
▸
Multi-configuration garment. Three wear states: gown, coat, separates. Modular seam system — no permanent closures.
The Pattern Room
Power Gown I — SS 2026
Merino Wool · Bonded Crepe · 380g
BODICE FRONT Cut 1
BODICE BACK Cut 1
SLEEVE Cut 2
SKIRT PANEL Cut 2 · Bias 45° bias
SHOULDER PAD Cut 2 · Bonded
—
—
—
—
The Material Dialogue
Live AI Observations
🧵 Bodice × Sleeve
Zero-ease set confirmed. Shoulder geometry intact. Sleeve cap sits precisely at geometric anchor point. Press hot before attaching.
Just now · Power Gown I
⚠ Waist Seam × Merino
Bias stretch detected at waist seam — 4.2mm drift on 60cm panel. Recommend twill tape stay before attaching skirt to bodice. Do not skip.
2 min ago · Power Gown I
✓ Shoulder Pad × Bodice
Geometric pad anchored at 3 basting points. Geometry locked. Press cold — heat will distort bonded layer.
5 min ago · Power Gown I
💡 Power Gown I × Power Gown III
Same sloper family. Transferring sleeve block from Gown I to Gown III will save 2 full pattern sessions. Collar attachment point differs — adjust 8mm at neckline seam.
12 min ago · Cross-garment
📐 Skirt Panel × Grain
45° bias cut confirmed for drape behavior. Stabilize all seam allowances before construction begins. Allow 48h for bias to settle after cutting.
18 min ago · Power Gown I
✓ Bonded Crepe × Shoulder Geometry
Bonded construction holds geometric shoulder without boning. No interfacing required. Confirmed travel-packable — folds to 28×34cm without deformation.
24 min ago · Fabric analysis
Ask about this garment
Construction
Intelligence
01
✓
Cut & Mark
All pieces cut. Notches marked. Bias grain confirmed on skirt panels.
02
✓
Stay & Stabilise
Twill tape stays applied. Bias seams stabilised. Shoulder seam reinforced.
03
Skirt Attach
⚠ Do not proceed until twill tape stay is confirmed at waist seam. Merino bias drift detected.
04
Bodice Seams
Stitch bodice side seams. Press all seams open — do not topstitch at this stage.
05
Sleeve Set
💡 Zero-ease sleeve. Ease cap precisely — deviation of >2mm will distort the shoulder geometry. Pin at 3 geometric anchor points before stitching.
06
Shoulder Pad
Tack geometric pad at 3 basting points. Press cold only — heat distorts bonded layer.
07
Final Press
⚠ Cold press only for bonded areas. Steam on reverse only. Do not iron direct on face — Merino bonding will separate.
08
QA & Sign-off
Measure shoulder geometry against spec. Confirm sleeve hang. Photograph finished garment before handover.